Smart Home Zigbee Light Switches, Online Manual and Help Guide.

ZigBee Smart Switch Online Help Guide and Installation Manual

WARNING:

Zigbee 1-4 gang Wall Switches Manual

◆ Supports 2 or 3 wire switch wiring. Optional neutral terminal
◆ High quality crystal tempered glass panel design, never fade
◆ With blue and red LED indicator
◆ E-start, no sparking contacts.
◆ Lamp status
◆ Support 2 way switching through Zigbee Controller 
◆ Supports Alexa and google home when paired with Zigbee Controller
◆ Applicable to all the common lamps, such as incandescent,
fluorescent lamps, led lamps ,motor and so on
◆ Suitable for home, office, hotel, hospital and villa so on

• Twist to remove, Open the front cover by a small flat screwdriver

• N wire connection is optional for 1-4 gang switches but if available its recommended.

 

• Cover the panel and connect the power. (After the power is on, please wait for 3 seconds for the touch sensitivity to calibrate then touch to turn on lamps.)

• Once safely wired and powered on ,click on/off button five times  consecutively and rapidly then hold the button for 5 seconds until  the buttons start to blink rapidly

• Add to your Zigbee Gateway (see below for more guides)

• Add Zigbee Switch

• Learning mode will exit if you have no operation after 3 minutes

Specification
AU Standard
Dimension: 120*72*37MM
Voltage: 110-240V~ AC/50~60Hz
Resistive Max. load 625W
Inductive Max. load 150W

Zigbee 3.0 IEEE 802.15.4

Warranty
This warranty covers defects in manufacturing that arise from
the correct use of the device. It is limited to defects in materials
or workmanship and does not cover damage caused by abuse,
misuse, unauthorised modification, power surge damage or
extreme heat or cold or corrosive environments. The warranty
also does not cover the normal wear and tear on covers, cases,
housings, connectors and accessories. The warranty does not
apply to any product with missing, altered or defaced serial
numbers. Your products come with a 12 month manufacturer’s
warranty as standard.

 

Zigbee Dimmer Wall Switches Manual

1. High quality tempered glass panel design,never fade.
2. With blue and red LED indicator,very distinguished.
3. Easy to install,replace the old switch directly.
4. Power metering function.
5. Check lamp status.
6. Support Amazon Alexa and Google Assistant ,etc.
7. Apply to incandescent lights, Dimmer LED light,etc.
Smart Dimmer Light Switch

• Twist to remove, Open the front cover by a small flat screwdriver

 

• Connect wire to the correct terminal and tighten the screws.

• Fix screws

• Cover the panel and connect the power. (After the power is on, please wait for 3 seconds for the touch sensitivity to calibrate then touch to turn on lamps.)

• Add to your Zigbee Gateway (see below for more guides)

• Add Zigbee Switch

• Learning mode will exit if you have no operation after 3 minutes

Operation:

• Touch the  button to turn on/off ,the  is to dim down, the  is to dim up

What can I do if lights flicker?

Flicker happen when the working current of LED lights is too low. We can increase voltage to solve this matter.

•  Press  and button for 5 seconds ,the brightness of light will be 50% .
• Touch arrow   button to increase or decrease brightness .
• Touch  button to save setting.

Specification

AUS Standard
Dimension: 120*72*37MM
Voltage: 110-240V AC/50~60Hz
Tungsten & Halogen lamp <600W
Dimmer LED lamp <20-300W

Technical:
Voltage regulation
Leading edge mode
Zigbee 3.0 IEEE 802.15.4

This warranty covers defects in manufacturing that arise from the correct
use of the device. It is limited to defects in materials or workmanship and
does not cover damage caused by abuse, misuse,unauthorised
modification, power surge damage or extreme heat or cold or corrosive
environments. The warranty also does not cover the normal wear and
tear on covers, cases, housings, connectors and accessories.
The warranty does not apply to any product with missing, altered or
defaced serial numbers. Your products come with a 12 month
manufacturer’s warrantly as standard.

 

 How to Connect to your Zigbee Controller

 SmartThings Edge Drivers:

1. Copy the following link into your browser;
https://bestow-regional.api.smartthings.com/invite/3X21zPWrPwlR
It is an Invite link to the OzEdgeDrivers Channel
2. Sign in with your SmartThings Login and then Select the Controller you wish to Enroll.
3. Then Click Available Drivers;

4. Locate the Drivers you need and press Install, they will then install onto your controller.

You will need to Exclude and Reinclude your devices to use the edge drivers.

 

Connect to  ZHA (Zigbee Home Automation) on Conbee 2 in Home Assistant.

Connect to Tuya Zigbee Hub

1. Connect the gateway to your router
2. Open”Smart Life”,click top right-hand”+”
3. Choose “Gateway and others”and choose the “gateway” click next until finished
4. Add new device by going to the + Button
5. Select Electrical
6. Light switch Zigbee

Zigbee2mqtt

How to connect to the ZemiSmart Zigbee Homekit Hub